Ask a Question
Welcome to the MotorForum.RfidEpc.CoM Servo & Stepper Motor Industrial Automation Technology Community Forum


+3 votes
115 views

Which 3D printer stepper motor drive chip is better? The best 3D printer stepper motors brand.

by (34.6k points)

6 Answers

+2 votes
 
Best answer

What chip should a 3D printer use?

The boon of the 3D printing industry - Trinamic launches the new TMC5160 powerful SilentStepStick. The TMC5160 is a high power stepper motor controller and driver IC with serial communication interface.

It combines a flexible automatic target positioning ramp generator with the industry's most advanced stepper motor driver.

Using an external transistor, highly dynamic, high-torque drive Based on Trinamic's advanced SpreadCycle and StealthChop chopper, the drive ensures absolutely noise-free operation with maximum efficiency and optimal motor torque.

by (116k points)
selected by
+2 votes

What is Two-Phase Stepper Motor Driver IC MS35776?
Overview of the perfect driver chip MS35776 for 3D printers, features and functions of MS35776
The MS35776 also provides a regulated 5V power supply output, which requires a capacitor between 2.2uF and 4.7uF for applications. There is a structure to detect V5 voltage, and if there is an abnormality (low voltage), all output tubes will be shut down.

The MS35776 is a high-precision, low-noise, two-phase stepper motor driver chip. The chip integrates fast mode and silent mode to meet different applications at high and low speeds. The chip has built-in power MOSFETs, and the average current can reach 1.4A and the peak current can reach 2A for long-term operation. The chip integrates over-temperature protection, under-voltage protection, and over-voltage
Protection functions for current protection, short ground protection, and short power protection.

by (128k points)
+2 votes

Key features

● 2-phase stepper motor, can reach a peak current of 2A

● Built-in MOS, STEP/DIR interface

● Voltage range 4.75~36V

● STEP/DIR interface, you can choose 2, 4, 8, 16, or 32 microsteps

● Built-in 256 segments

● The motor automatically enters the power-saving mode when it is stationary

● Built-in sense resistor mode optional (no external sense resistor required)

by (116k points)
+1 vote

TMC2209 is a stepper motor driver chip from the German company Trinamic, those interested in the interior of the 3D printer will hear more about it in the near future, because this chip will bring you a new experience.

by (62.8k points)
+2 votes

The 3D printer stepper driver Allegro A4988, while not having a mute feature, only requires a small heatsink to keep itself below its thermal limit.

by (128k points)
+2 votes

What kind of stepper motor is generally used in 3D printers?
Desktop level 3D printer, generally with 42 stepper motor is enough, the current can be 1.5A is no problem, the general current with 1A is enough, the specific motor model you consider yourself, is the cost performance problem, you for 3D printer just consider a few problems: 1 current , as mentioned above, 1.5A should be no problem, unless you have special requirements 2 axis diameter, generally 3D printers are driven by timing belts, so synchronizer wheels and couplings are required, Choose your shaft diameter according to these two, which is generally more than 5mm.

by (128k points)

Related questions

+1 vote
3 answers 58 views
+1 vote
1 answer 405 views
405 views asked Aug 12, 2024 by Stepper-Motor (116k points)
+1 vote
2 answers 72 views
+3 votes
15 answers 138 views
+2 votes
1 answer 115 views
115 views asked Apr 14, 2023 by Motor Manufacturers (34.6k points)
+3 votes
5 answers 168 views
...